Analysis Software

If you would like access to the software on this page we ask that you adhere to a few basic conditions:

• You don't share it further than your group, but direct any additional requests to us
• We will answer simple questions and try to add requested features and especially fix bugs, but we can't "support" the software as if it were a commercially available package, we also will not answer basic Igor questions.
• If eventually your group makes improvements, we'd like to have those shared back and ideally keep a master version.

All files on this page require proper credentials for download. Please contact us if you would like access to the files or to report any bugs with the software: password request

ICARTT

ICARTT Software

Software	Version	Notes	Link
ICARTT Loader and File Creation Tool	2013	Donna Sueper and Ken Aiken ICARTT Documentation	2013 General Macros (.ipf) 2013 ICARTT Format (.ipf)

ICARTT Software Notes

• These functions create and load data files of the format indicated in the 2008 ICARTT Data Management Plan document, which was roughly based on the Haines-Hipskind NASA Ames Format. Functions and macros herein are not appropriate for all data generated by ICARTT participants; assumptions are outlined below.
• Functions in this file use functions in the 2008 GeneralMacros (latest version) igor procedure file. Users should have both files open in an igor experiment.
• Whenever a user loads or creates a ICARTT format file, an igor data folder called ICARTTFileFormat gets created in the experiment and most of the work is done here. If something goes awry, the user can reset the data folder to root (most everyone's default)by inserting the text below (less the //) into the command line SetDataFolder root:
• Some parameters are calculated; some have simple default values. They are:
  • NumHeaderLines - gets calculated
  • FileFormatType = 1001 // this value is assumed for reading and creating files.
  • FileVolumeNumber = 1 // this value is assumed for reading and creating files.
  • TotalVolumeNumber = 1 // this value is assumed for reading and creating files.
  • UTCDataStart - set from selected time wave
  • NumVariables - gets set when user selects waves
  • ScaleFactor = 1 // this value is assumed for reading and creating files.
  • MissingDataIndicator = -9999 // NOTE - The same missing value is used for all parameters when creating a file.
  • NumSpecialCommentLines - gets calculated
  • NumNormalCommentLines - gets calculated
  • Normal Comments are the concatenation of several other parameters
• None of the original waves in the experiment are modified in any way. Waves selected to be saved are duplicated in the ICARTTFileFormat data folder. The UTC timewave (the independent parameter) and any dependent parameters formatted with a "t" (from the create panel) will have the starting date subtracted from it (in the created file) and will be formatted with one digit after the decimal.
• When loading an icartt file into an experiment, the missing value as reported in the header will be used to convert missing values in the incoming waves to nans. The independent variable (time) will have the UTC date (as indicated in the header) added to it.
• When loading data from the LoadDataOnly menu item, almost no format checking is done and missing data isn't changed to nans.
• The name of the wave in the experiment will be the name given to the dependent and independent parameters, with the exception of matricies, where column names much as mymatrix0, mymatrix1, etc are used.
• If anything is named in the experiment in a 'liberal' fashion (i.e. wave names with spaces), all bets are off.
• Users should be aware that there are opearting system differences for end of line designations. Mac uses carriage return (CR), Unix uses line feed (LF), and Windows use carriage return + line feed (CRLF) For icarrtt, the preferred end of line designation is CRLF (which correspondes to \r\n in the code).

Picarro G2401

Picarro Software

Software	Version	Notes	Link
Picarro G2401 Loader and Data Plotting	v1.0	First release by Michael Lechner	Picarro Panel (.ipf)

Picarro Software Notes

• Picarro Panel v1.0 (MJL 02/05/2013)
  • Recursively loads all .DAT Picarro acquisition files or a specified date range of files in a given directory (best to point the loading directory to DataLog_User and leave the sub directories in their original configuration)
  • Plots:
    • Picarro measurement time series
      • CH4 / CH4 dry
      • CO
      • CO2 / CO2 dry
      • H2O
    • Picarro diagnostic time series
      • Das Temperature
      • Etalon Temperature
      • Warm Box Temperature
      • Cavity Temperature
      • Cavity Pressure

Software Output

Measurement Timeseries

Diagnostic Timeseries

Real Time AMS Igor Display

Real Time Software

Software	Version	Notes	Link
Real Time AMS Igor Display	v10	First release Donna Sueper and Mike Cubison Modified by Michael Lechner	DAQ_QuickView.ipf

Software Output

Aircraft Data Plot

SMPS

SMPS Software

Software	Version	Notes	Link
SMPS data loader	v4	First release Doug Day (built on MJC's original loader)	JG_SMPS_v4.pxt Example experiment Sample AIM exported text files

SMPS Software Notes

JG_SMPS_V4 (dd 1/12/11)

• Loads and Concatenates SMPS data collected with TSI AIM (built on Mike C's BEARPEX/CalNex JG_SMPS_v3.ipf and uses ToolsMJC_v1a.ipf and Tools_20100221.ipf)
• Input should be .txt files created as ouput in TSI AIM software (row-formatted) and dNdLogDp and in named in format: 2010_12_13_1522_SMPS.txt (yyyy_mm_dd_hhmm_SMPS.txt)
• "Load-Concatenate" button promps user to select folderpath for text files to load

and also promps user to input assign "project" name to files loaded (will put all data in folder names as such

• Image Time Series Plots plots either number or mass distributions (density approximated as 1.0 g/cm3)

Optional inputs for: Interpolation across data gaps Dp smoothing Max percentile of data assigned to hottest color in image (help use full color range)

• Integrated # and Mass Concentration Plot (Number or Mass)

Optional inputs: Max/Min Dp over which to integrate total concentration

Additional Notes:

• Best to reselect "Data Folder to Plot" to be sure that datafolder is set to proper project folder (should be reset after all plotting, so only really needed if user changes datafolders). However, must select before first plot.
• Panel inputs stored in root:Temporary (DO NOT DELETE this folder) - can delete all other folders

Next Version Steps:

• some QC functions like in CalNex example
• option for mask waves

Software Output

dNdlogDp Size Distribution

dMdlogDp Size Distribution

dN Total Concentration

dM Total Concentration