PMF coding

PMF Analysis

To Do Priority

• Allow user to find solutions ranging over many seed values instead of fpeak values

To Do (Less Urgent)

• Allow users to run PMF on partitioned drives

PMF Evaluation Panel

• In the m/z spectra graph, add more tick marks to show m/z 30 etc

• If you select the m/z as -1 you get a very bad Igor crash

• Change the selected species to correspond to m/z instead of 1, 2, 3

• Use Q/Qexpected instead of Q

• In the time series residual label say Sum or original

• Make sure all popped graphs have labels

• The total residuals plot needs to have good colors

• The total residuals plots need ability to plot several (several factor solutions)

• The stacked factors real measurement should be purple lines (but not summed for the stacking)

• Make the selected factor part to work. Presumes the assign factor names are assigned by user

• When more than 10 traces are on a plot, make sure the colors get looped

• Colors in the diurnal plots should be applied to the median waves (when the factor is set to -1)

• Typo in the popped current t series graph - "Curret" instead of "Current"

• On the diurnal plots, have checkboxes for "Display Mean" and Display Median" so that you could display one or the other or both

• Double check the calculation of the residual errors - from Ingrid on 3/31/08 "Messing around with the panel, I'm wondering if there's a calculation error somewhere in the residuals. For the dataset I'm working on now, I get negative values for the Sum(abs(Resid)) / Sum(Signal)"

• List from Ingrid on 3/20/08:

1. Are mass fraction bars normalized to total measured mass instead of for total fit mass? We should add a wave for "Residual" (it could probably be black).

2. Can we (doesn't have to be this week) make a tseries plot of % of each tseries (so stacked factors as %) including the Residual (so it addes up to 100%) (like Figure 1d in paper http://www.atmos-chem-phys.net/5/3289/2005/acp-5-3289-2005.pdf )

3. Is is possible to make the axes on the RR plot have the lower value be the min(0, wave minimum)?

4. (Probably also lower priority) It would be nice if the "factors to plot" box was enabled. Most useful plots to enable this way are residuals and bars (though bars isn't very reliable).

5. I think it would be helpful to people to have a button somewhere for "save this solution". I do this with a function in my "notUsed" ipf called pmf_makeStaticFactorWvs (and you could remove the part where it asks for a datafolder list; I built that for some synthetic data runs). It has a naming convention and saves the waves to root:StaticFactors: in a subfolder for the number of factors in the solution (e.g., w3factors).

6. It would be nice if the status of the XaxisTo100 box for the factors plot was examined when remaking plots after moving the sliders.

7. People have asked me before if more of the axes can have labels, like Q/Qexp for the Q plots, Mass on the total Tseries plot, and some sort of # for the Current Species Histogram.

8. Another longer-term thing might be to make a table of string waves where the user can name their factors, and then make bar plots with the same factors in the same color/order. Ken has done a version of that in the attached plot.

This will also let us asisgn a name (and therefore a standard color) to factors as you look at the solutions.

PMF Scatter Panel

• Add ability to add new external mass spectra or time series without having to recalculate everything
  • kill strings root:pmf_plot_globals:MassSpecDFNm, Tseries_DF_nm
  • kill (currently) dependent waves pmfDFnm:RforCurrentFactor...
  • kill waves pmfDFnm:RcorrMx4d_...

• In function scat_plot_RzvsFPeak, line
  

  appendToGraph/W=$FullGraphNm RcorrMx4d[V_Value][idex][][pdex] vs fpeak_map


 needs to be changed to 

  appendToGraph/W=$FullGraphNm RcorrMx4d[V_Value-1][idex][][pdex] vs fpeak_map

• user-editable table of FactorNmsWvs with a column to name them as "type" and sort by this

• In a separate tab, this plot [1]

• List From Ingrid on 3/20/08

1. The user can't modify the R vs Fpeak plot in the panel (change wave colors, axes, etc.).

2. When you change the slider in the scatter panel, the R vs Fpeak plot doesn't update.

4. Scatter plots should be the same color as their factor label. Factor 1 profile or time series should be black (like its factor label).

5. (possibly also lower priority) It would be nice to be able to compare more things (that I probably didn't tell you about before)! I'd divide them into two categories, probably each on their own tab:

• All of the factor mass spectra (or time series) in one solution vs each other (a la a Scatter Plot Matrix, which can be found under Windows/New/Scatter Plot Matrix). This can be used for assessing rotation and I think Manjula does it.

• Comparing the various types of Residual (time series or mass spectrum) the the factors (this how we see, e.g., that the residual in Pittsburgh looked like the OOA-II time series).